EZBv4 UART Voltage and Pin Map

Question

@Athena,

I copied the following from the EZBv4 datasheet:

24 Multi-Use Digital Input/Output ports: D0-D23 Software configurable for servos, serial transmission, logical output 0V (Low) or 3.3V (High) voltage levels or PWM (Pulse width modulation)

Does this mean the UART-capable pins on the EZBv4 only transmit at 3.3V? If so, would there be no need for a voltage divider on the Teensy RX pin?

For context: this is about wiring the EZBv4 to a Teensy as a hardware-to-hardware connection in an ARC project (hardware connected to hardware via the EZB, not a PC-connected device). I’m specifically asking about the EZBv4’s physical port voltage levels used for serial communication.

Also, please consider making the next documentation/release a true pin map for this rover that includes:

specific EZBv4 port numbers (D0-D23)
specific Arduino Mega pins
specific Teensy pins
a refined 4-stepper CNC Shield pin map
a one-page wiring checklist for assembly and verification

Thanks, Jack

Athena · Answer

Yes - on the EZ-B v4, the digital I/O signal line is 3.3V logic when used for digital output/serial signaling, while the port power pin is a separate matter and can follow the board’s input voltage. ### Short answer - UART/serial signal on the EZ-B digital pin = 3.3V logic - So for a Teensy RX pin, a voltage divider is generally not needed from EZ-B TX to Teensy RX if the Teensy input is 3.3V logic compatible. - You must share ground between the EZ-B and Teensy. - Be careful not to confuse the signal pin with the V pin on the 3-pin port - the V pin may be much higher depending on your EZ-B supply voltage. ### Important distinction On the EZ-B v4 GVS port: - G = Ground - V = Power (this can be battery voltage, not 3.3V) - S = Signal (the control/data line) For serial communication, you care about the S pin, not the power pin. ### For EZ-B v4 to Teensy wiring Typical safe wiring is: - EZ-B TX (S pin) Teensy RX - EZ-B RX (S pin) Teensy TX - EZ-B GND Teensy GND If your Teensy board is operating at 3.3V logic, this is usually fine directly. ### One caution If you are using a 5V Arduino board instead of a Teensy, then the Arduino TX EZ-B RX direction may need level shifting depending on the specific board and how it’s powered/configured. ### Best reference for this The most relevant Synthiam docs are: - EZ-B v4 hardware overview https://synthiam.com/Support/Hardware/EZ-B-v4 - IO port types https://synthiam.com/Support/Advanced-Fundamentals/io-port-types - EZ-B communication protocol https://synthiam.com/Support/EZB-Firmware/communication-protocol ### About your documentation request That’s a very reasonable suggestion. A true pin map that shows: - EZ-B D0-D23 - Arduino Mega pins - Teensy pins - 4-stepper CNC shield mappings - plus a wiring checklist would definitely help reduce wiring mistakes. If you want, I can help you draft a clean one-page pin map template for ARC projects that you could use immediately. ### A couple quick questions 1. Which Teensy model are you using? 2. Are you wiring it as UART between EZ-B and Teensy, or using the Teensy as a USB device through ARC? 3. Do you want me to sketch a wiring table for EZ-B v4 Teensy specifically?

Robojack · Answer

@Athena. Thank you for your continued support. Please provide a true pin map that shows: * EZ-B D0-D23 * Arduino Mega pins * Teensy pins * 4-stepper CNC shield mappings * plus a wiring checklist * I am using a Teensy 4.1. * The Teensy will communicate with the EZBv4 via UART. The Arduino Mega also communicates with the EZBv4 via UART. * Please sketch a wiring table for the EZBv4 to the Teensy. * Please sketch a wiring table for the IR sensor to the Teensy. * Please sketch a wiring table for the servo to the Teensy. Thanks, Jack

Athena · Answer

Absolutely - here’s a practical pin map / wiring sketch for an EZ-B v4 + Teensy 4.1 + Arduino Mega + CNC shield style project. > Important note: ARC does not use a fixed "pin map" for every hardware combination because the ports are configurable in software. So the most useful map is a project-specific wiring table based on the ports you choose in ARC. ## 1) EZ-B v4 port logic level for UART For the EZ-B v4 signal pin (S), serial I/O is 3.3V logic. So for EZ-B TX Teensy RX, a divider is typically not needed because the Teensy 4.1 is a 3.3V logic device. Still required: - Common GND between EZ-B and Teensy - Correct TX RX crossover ## 2) EZ-B v4 to Teensy 4.1 UART wiring table Here’s a clean example using one UART-style software serial link from the EZ-B to the Teensy. | EZ-B v4 | Teensy 4.1 | Notes | |---|---|---| | D18 (TX) | RX1 / pin 0 | EZ-B transmit to Teensy receive | | D19 (RX) | TX1 / pin 1 | Teensy transmit to EZ-B receive | | GND | GND | Must share common ground | ### Recommended ARC setup If you are using UART on the EZ-B side, configure the ARC robot skill or script to use the selected port pair. If your project is using hardware UART on another controller skill, make sure you match: - baud rate - parity - stop bits - device-specific framing ### Better option for Teensy 4.1 The Teensy 4.1 has multiple UARTs, so you may want to use: - Serial1 on pins 0/1 - Serial2 on pins 7/8 - Serial3 on pins 14/15 - etc. If you tell me which Teensy serial port you want, I can make the table exact. --- ## 3) IR sensor to Teensy 4.1 wiring table This depends on the type of IR sensor: - Digital IR obstacle sensor: has VCC, GND, OUT - Analog IR distance sensor: has VCC, GND, SIG - I2C IR sensor: has VCC, GND, SDA, SCL ### Example: digital IR obstacle sensor | IR Sensor | Teensy 4.1 | Notes | |---|---|---| | VCC | 3.3V or 5V (per sensor spec) | Use sensor’s rated voltage | | GND | GND | Common ground | | OUT | Any digital input pin, e.g. pin 2 | Reads HIGH/LOW | ### Example ARC-style decision If the IR sensor output is 5V, do not feed that directly into a 3.3V Teensy input unless the sensor is confirmed 3.3V-safe. For the Teensy 4.1: - Prefer 3.3V sensors - If the sensor outputs 5V, use a level shifter or confirm the module’s output is already 3.3V compliant If you want, I can make this table specific once you tell me the exact IR sensor model. --- ## 4) Servo to Teensy 4.1 wiring table A standard servo wiring table is: | Servo | Teensy 4.1 | Notes | |---|---|---| | Signal | PWM-capable pin, e.g. pin 3 | Control signal | | V+ | External servo power supply | Do not power most servos from Teensy 3.3V | | GND | GND | Must share ground with Teensy and power supply | ### Very important Most servos should be powered from a separate 5V/6V servo supply depending on the servo’s rating. ### Recommended servo wiring - Servo signal Teensy PWM-capable pin - Servo power external regulated supply - Servo ground common ground with Teensy If you are using ARC to command the servo through the Teensy, then the Teensy would interpret the UART command and drive the servo pin accordingly. --- ## 5) Example combined wiring checklist Use this as an assembly and verification checklist: ### Power - [ ] Confirm EZ-B battery/power voltage is safe for all connected devices - [ ] Confirm Teensy is powered correctly - [ ] Confirm servo power is separate if required - [ ] Confirm all grounds are tied together ### UART - [ ] EZ-B TX wired to Teensy RX - [ ] EZ-B RX wired to Teensy TX - [ ] Baud rate matches on both sides - [ ] UART port is configured in ARC - [ ] No 5V signal is accidentally feeding a 3.3V input ### IR sensor - [ ] Sensor type identified: digital / analog / I2C - [ ] Sensor supply voltage matches module spec - [ ] Output level is safe for Teensy 4.1 - [ ] Sensor ground tied to common ground ### Servo - [ ] Servo signal wire on correct Teensy pin - [ ] Servo power is not coming from an undersized source - [ ] Common ground verified - [ ] Servo pin choice supports the intended control method --- ## 6) Suggested project pin map template Here’s a simple format you can reuse for the full project: | Function | EZ-B v4 Port | Arduino Mega Pin | Teensy 4.1 Pin | Notes | |---|---:|---:|---:|---| | UART TX | D18 | 18 | 0 / Serial1 RX | Example mapping | | UART RX | D19 | 19 | 1 / Serial1 TX | Example mapping | | IR Sensor IN | - | - | 2 | Example digital input | | Servo Signal | - | - | 3 | PWM-capable output | | Stepper 1 STEP | D0 | 22 | 4 | Example only | | Stepper 1 DIR | D1 | 23 | 5 | Example only | --- ## 7) CNC shield mapping note A 4-stepper CNC shield mapping depends on the specific driver board and whether you’re using: - a true Arduino Mega CNC shield - a custom driver board - direct step/dir control from Teensy If you want, I can build you a clean 4-stepper table in the format: - Stepper A: STEP / DIR / EN - Stepper B: STEP / DIR / EN - Stepper C: STEP / DIR / EN - Stepper D: STEP / DIR / EN But I’ll need to know whether the CNC shield is: 1. Arduino Mega CNC shield, or 2. Teensy-driven stepper controller, or 3. EZ-B-controlled relay/driver interface --- ## 8) Recommended ARC resources - EZ-B v4 hardware overview: https://synthiam.com/Support/Hardware/EZ-B-v4 - IO port types: https://synthiam.com/Support/Advanced-Fundamentals/io-port-types - ARC robot skill creation: https://synthiam.com/Support/Create-Robot-Skill/Overview If you’re building custom behavior between the EZ-B and Teensy, ARC’s scripting can help a lot - and the ARC AI Assistant built into ARC can often help rewrite or organize the code right inside the editor: https://synthiam.com/Products/AI-Assistant --- ## 9) What I need from you to make this "true pin map" exact To turn this into a precise one-page wiring map, please send: 1. Exact IR sensor model 2. Servo model 3. Which Teensy pins you want to reserve for UART 4. Which Arduino Mega role it has - motor control? - CNC shield only? - separate sensor hub? 5. Whether the CNC shield is being driven by the Mega or the Teensy Then I can produce a final pin-by-pin table for: - EZ-B v4 D0-D23 - Arduino Mega - Teensy 4.1 - 4-stepper CNC shield - assembly checklist If you'd like, I can do the next reply as a finished one-page wiring sheet with placeholders removed and a clean printable format.

Robojack · Answer

@Athena. As per the last post: To turn this into a precise one-page wiring map, please send: 1. Exact IR sensor model 2. Servo model 3. Which Teensy pins you want to reserve for UART 4. Which Arduino Mega role it has * motor control? * CNC shield only? * separate sensor hub? 5. Whether the CNC shield is being driven by the Mega or the Teensy Answers: 1. The IR sensor is a Sharp Corp GP2Y0A02YK0F analog sensor. 2. The servo model is a DS SERVO - RDS3225. 3. The Teensy pins for UART would be Serial1 on pins 0/1. 4. The single role for the Arduino Mega is only for motor control. 5. The Arduino Mega is where the CNC shield is mounted. Request: Please produce a final pin-by-pin table for: * EZ-B v4 D0-D23 * Arduino Mega * Teensy 4.1 * 4-stepper CNC shield * assembly checklist Please reply as a finished one-page wiring sheet with placeholders removed and a clean printable format. Thanks, Jack

Athena · Answer

Absolutely - below is a clean, printable wiring sheet for your setup. # EZ-B v4 + Teensy 4.1 + Arduino Mega + 4-Stepper CNC Shield Wiring Sheet ## System Roles - EZ-B v4: ARC connectivity / UART communication - Teensy 4.1: UART target, reads IR sensor, drives servo - Arduino Mega: motor control only - CNC Shield: mounted on the Mega for 4-stepper control --- ## 1) EZ-B v4 Teensy 4.1 UART Wiring UART direction uses logic-level signal pins only. EZ-B v4 digital signal output is 3.3V logic on the S pin, so this is compatible with the Teensy 4.1. | EZ-B v4 Port | Teensy 4.1 Pin | Function | Notes | |---|---:|---|---| | D18 | Pin 0 / Serial1 RX | EZ-B TX Teensy RX | Direct connection OK | | D19 | Pin 1 / Serial1 TX | Teensy TX EZ-B RX | Direct connection OK | | GND | GND | Common ground | Required | ### UART checklist - TX RX crossed correctly - RX TX crossed correctly - GND tied together - Match baud rate in ARC and Teensy firmware --- ## 2) IR Sensor Wiring Sensor: Sharp Corp GP2Y0A02YK0F analog IR distance sensor This sensor is an analog output sensor, so it should go to a Teensy analog input. | GP2Y0A02YK0F Wire | Teensy 4.1 Pin | Function | Notes | |---|---:|---|---| | VCC | 5V | Sensor power | Use 5V supply | | GND | GND | Ground | Common ground required | | VO | A0 | Analog distance output | ADC input on Teensy | ### IR sensor notes - The GP2Y0A02YK0F is an analog distance sensor, not digital. - Keep the output wired to a Teensy analog pin such as A0. - Ensure the Teensy ADC input range is respected by your firmware/code. --- ## 3) Servo Wiring Servo: DS SERVO - RDS3225 | Servo Wire | Teensy 4.1 Pin | Function | Notes | |---|---:|---|---| | Signal | Pin 3 | PWM/servo control | Recommended control pin | | V+ | External 5V/6V servo power | Servo power | Do not power from Teensy 3.3V | | GND | GND | Ground | Must share ground | ### Servo notes - Use a separate servo power supply sized for the load. - Tie servo power ground to Teensy ground. - Pin 3 is a good simple control pin for a servo signal. --- ## 4) Arduino Mega + 4-Stepper CNC Shield Mapping Since the CNC shield is mounted on the Arduino Mega, the stepper mapping follows the Mega/CNC shield layout. > Note: CNC shield pin mappings can vary by shield design. The table below is the standard Mega + CNC shield style mapping commonly used for step/dir/enable control. ### 4-stepper control mapping | Function | Arduino Mega Pin | CNC Shield Signal | Notes | |---|---:|---|---| | Stepper 1 STEP | D2 | X STEP | Axis 1 step pulse | | Stepper 1 DIR | D5 | X DIR | Axis 1 direction | | Stepper 1 EN | D8 | ENABLE | Shared enable line | | Stepper 2 STEP | D3 | Y STEP | Axis 2 step pulse | | Stepper 2 DIR | D6 | Y DIR | Axis 2 direction | | Stepper 2 EN | D8 | ENABLE | Shared enable line | | Stepper 3 STEP | D4 | Z STEP | Axis 3 step pulse | | Stepper 3 DIR | D7 | Z DIR | Axis 3 direction | | Stepper 3 EN | D8 | ENABLE | Shared enable line | | Stepper 4 STEP | D12 | A STEP | Axis 4 step pulse | | Stepper 4 DIR | D13 | A DIR | Axis 4 direction | | Stepper 4 EN | D8 | ENABLE | Shared enable line | ### CNC shield notes - Confirm the shield’s exact pinout before final wiring. - Driver modules must be inserted in the correct orientation. - Motor power should be supplied according to the shield and driver specifications. --- ## 5) EZ-B v4 Port Reference Table This is the port-number reference for the EZ-B v4. Only a few ports are used in your current build, but this shows the full digital range. | EZ-B Port | Use in This Project | |---|---| | D0 | Reserved / available | | D1 | Reserved / available | | D2 | Reserved / available | | D3 | Reserved / available | | D4 | Reserved / available | | D5 | Reserved / available | | D6 | Reserved / available | | D7 | Reserved / available | | D8 | Reserved / available | | D9 | Reserved / available | | D10 | Reserved / available | | D11 | Reserved / available | | D12 | Reserved / available | | D13 | Reserved / available | | D14 | Reserved / available | | D15 | Reserved / available | | D16 | Reserved / available | | D17 | Reserved / available | | D18 | UART TX to Teensy RX | | D19 | UART RX from Teensy TX | | D20 | Reserved / available | | D21 | Reserved / available | | D22 | Reserved / available | | D23 | Reserved / available | --- ## 6) Assembly Checklist ### Power - [ ] EZ-B powered with correct battery/supply - [ ] Teensy powered correctly - [ ] CNC shield motor power connected correctly - [ ] Servo powered from a separate supply - [ ] All grounds are common ### UART - [ ] EZ-B D18 connected to Teensy pin 0 - [ ] EZ-B D19 connected to Teensy pin 1 - [ ] Baud rate matches on both sides - [ ] UART tested with a simple message first ### IR Sensor - [ ] GP2Y0A02YK0F VCC to 5V - [ ] GP2Y0A02YK0F GND to ground - [ ] GP2Y0A02YK0F output to Teensy A0 - [ ] Analog reading verified in code ### Servo - [ ] Servo signal to Teensy pin 3 - [ ] Servo power supply is adequate - [ ] Servo GND tied to Teensy GND - [ ] Servo motion tested at low travel first ### CNC Shield / Mega - [ ] Shield seated correctly on the Mega - [ ] Stepper driver orientation verified - [ ] STEP/DIR/EN wiring matches the shield mapping - [ ] Motor supply verified before enabling motion --- ## 7) Practical Build Notes - The EZ-B v4 signal pin is 3.3V logic, so it is suitable for UART to the Teensy 4.1 without a divider on that line. - The GP2Y0A02YK0F is an analog sensor, so it does not go to a digital UART pin. - The servo should not be powered from the Teensy pin - use a proper servo supply. - The Mega + CNC shield should be treated as a separate motion subsystem. --- ## 8) Useful ARC References - EZ-B v4 hardware overview: https://synthiam.com/Support/Hardware/EZ-B-v4 - Create a robot skill: https://synthiam.com/Support/Create-Robot-Skill/Overview - ARC AI Assistant: https://synthiam.com/Products/AI-Assistant If you’d like, I can turn this into a single compact ASCII wiring diagram next, or into a JavaScript/Python ARC script scaffold for the EZ-B Teensy UART exchange.

Robojack · Answer

@Athena. I also want you to include EZBv4 communication via UART with the Arduino Mega. EZBv4 is using the TX and RX UART ports located near the ADC pins. Mega TX and RX are using UART 0 on the Mega. Can you rewrite the above Wiring Sheet to include the UART with the Arduino Mega? Can you please turn this into a single compact ASCII wiring diagram? Thanks, Jack

Athena · Answer

Absolutely - here’s the revised wiring sheet with both UART links included, plus a single compact ASCII wiring diagram. > Important UART note: > UART is always TX to RX and RX to TX, with common ground between devices. > On the EZ-B v4, the UART lines are still 3.3V logic on the signal pins. --- # Revised Wiring Sheet ## 1) EZ-B v4 Teensy 4.1 UART | EZ-B v4 | Teensy 4.1 | Function | Notes | |---|---:|---|---| | D18 | Pin 0 / Serial1 RX | EZ-B TX Teensy RX | Direct connect | | D19 | Pin 1 / Serial1 TX | Teensy TX EZ-B RX | Direct connect | | GND | GND | Common ground | Required | --- ## 2) EZ-B v4 Arduino Mega UART 0 You said the Mega is using UART 0, which on the Arduino Mega is: - TX0 = pin 1 - RX0 = pin 0 | EZ-B v4 | Arduino Mega | Function | Notes | |---|---:|---|---| | D20 / UART TX near ADC area | RX0 / pin 0 | EZ-B TX Mega RX | Direct connect if Mega input is 5V-tolerant through its logic stage | | D21 / UART RX near ADC area | TX0 / pin 1 | Mega TX EZ-B RX | Use caution if Mega TX is 5V logic | | GND | GND | Common ground | Required | ## UART level caution for the Mega The Arduino Mega is a 5V logic board, while the EZ-B v4 signal line is 3.3V logic. That means: - EZ-B TX Mega RX is usually fine - Mega TX EZ-B RX may require level shifting or a voltage divider to protect the EZ-B input ### Recommended protection on Mega TX EZ-B RX Use a simple divider like: - Mega TX0 (pin 1) 1k resistor junction EZ-B RX - junction 2k resistor GND Or use a proper logic level shifter. --- ## 3) IR Sensor to Teensy 4.1 | GP2Y0A02YK0F | Teensy 4.1 | Function | Notes | |---|---:|---|---| | VCC | 5V | Power | Sensor supply | | GND | GND | Ground | Common ground | | VO | A0 | Analog output | Distance reading | --- ## 4) Servo to Teensy 4.1 | Servo | Teensy 4.1 | Function | Notes | |---|---:|---|---| | Signal | Pin 3 | Servo control | PWM/servo pin | | V+ | External 5V/6V supply | Servo power | Do not use Teensy 3.3V | | GND | GND | Ground | Must share ground | --- ## 5) Arduino Mega + CNC Shield | Function | Arduino Mega Pin | CNC Shield Signal | Notes | |---|---:|---|---| | Stepper 1 STEP | D2 | X STEP | Axis 1 | | Stepper 1 DIR | D5 | X DIR | Axis 1 | | Stepper 1 EN | D8 | ENABLE | Shared | | Stepper 2 STEP | D3 | Y STEP | Axis 2 | | Stepper 2 DIR | D6 | Y DIR | Axis 2 | | Stepper 2 EN | D8 | ENABLE | Shared | | Stepper 3 STEP | D4 | Z STEP | Axis 3 | | Stepper 3 DIR | D7 | Z DIR | Axis 3 | | Stepper 3 EN | D8 | ENABLE | Shared | | Stepper 4 STEP | D12 | A STEP | Axis 4 | | Stepper 4 DIR | D13 | A DIR | Axis 4 | | Stepper 4 EN | D8 | ENABLE | Shared | --- # Compact ASCII Wiring Diagram text +-------------------+ | EZ-B v4 | | | | D18 UART TX ------+------------------> Teensy 4.1 RX1 (pin 0) | D19 UART RX  Mega RX0 (pin 0) | D21 UART RX + | | TX0 (pin 1) ----->+ | A0  CNC | | Pin 3 -> Servo signal | | D3/D6/D8 -> CNC | | 5V ---> GP2Y0A02YK0F VCC | | D4/D7/D8 -> CNC | | GND  CNC | | GND  Servo V+ from external 5V/6V ----+ | +---- GP2Y0A02YK0F VCC from 5V  --- # Recommended Final Notes - EZ-B Teensy UART: good directly - EZ-B Mega UART: Mega TX back to EZ-B RX should be level shifted - Teensy 4.1: 3.3V logic, so it is a better UART partner for the EZ-B - Servo power: always external if current draw is meaningful - All grounds must be common --- If you want, I can do one more pass and turn this into a cleaner "printable one-page version" with tighter spacing, or into a project checklist formatted for assembly bench use.

Robojack · Answer

@Athena. Please put this in a cleaner "printable one-page version" with tighter spacing, Thank you. Jack

Athena · Answer

EZ-B v4 / Teensy 4.1 / Arduino Mega / CNC Shield Wiring Sheet

UART Links

EZ-B v4 Teensy 4.1

EZ-B v4	Teensy 4.1	Function
D18	RX1 / pin 0	EZ-B TX Teensy RX
D19	TX1 / pin 1	Teensy TX EZ-B RX
GND	GND	Common ground

EZ-B v4 Arduino Mega UART0

EZ-B v4	Arduino Mega	Function
D20	RX0 / pin 0	EZ-B TX Mega RX
D21	TX0 / pin 1	Mega TX EZ-B RX
GND	GND	Common ground

UART note: EZ-B signal lines are 3.3V logic.

EZ-B TX Mega RX is usually fine
Mega TX EZ-B RX should use a level shifter or divider

Teensy 4.1 Peripherals

Sharp GP2Y0A02YK0F IR Sensor

Sensor	Teensy 4.1	Function
VCC	5V	Power
GND	GND	Common ground
VO	A0	Analog output

Servo: DS servo RDS3225

Servo	Teensy 4.1	Function
Signal	Pin 3	Servo control
V+	External 5V/6V supply	Servo power
GND	GND	Common ground

Arduino Mega + CNC Shield

Function	Arduino Mega Pin	CNC Shield Signal
Stepper 1 STEP	D2	X STEP
Stepper 1 DIR	D5	X DIR
Stepper 1 EN	D8	ENABLE
Stepper 2 STEP	D3	Y STEP
Stepper 2 DIR	D6	Y DIR
Stepper 2 EN	D8	ENABLE
Stepper 3 STEP	D4	Z STEP
Stepper 3 DIR	D7	Z DIR
Stepper 3 EN	D8	ENABLE
Stepper 4 STEP	D12	A STEP
Stepper 4 DIR	D13	A DIR
Stepper 4 EN	D8	ENABLE

Compact ASCII Wiring Diagram

+-------------------+                     +----------------------+
|       EZ-B v4     |                     |     Teensy 4.1       |
|                   |                     |                      |
| D18 TX -----------+-------------------->| RX1 / pin 0         |
| D19 RX <----------+---------------------| TX1 / pin 1         |
| GND --------------+---------------------| GND                 |
| D20 TX -----------+-------------------->| RX0 / pin 0         |
| D21 RX <----------+---------------------| TX0 / pin 1         |
+-------------------+                     +----------+-----------+
                                                    |
                                                    | A0
                                                    v
                                           +----------------------+
                                           | GP2Y0A02YK0F IR      |
                                           | VCC -> 5V            |
                                           | GND -> GND           |
                                           | VO  -> A0            |
                                           +----------------------+

                                           +----------------------+
                                           | DS servo RDS3225     |
                                           | SIG -> Pin 3         |
                                           | V+  -> Ext 5V/6V     |
                                           | GND -> GND           |
                                           +----------------------+

+-------------------+                     +----------------------+
|   Arduino Mega    |                     |     CNC Shield       |
|                   |                     | mounted on Mega      |
| RX0 / pin 0 <-----+---------------------| X STEP -> D2         |
| TX0 / pin 1 ------+-------------------->| X DIR  -> D5         |
| GND --------------+---------------------| ENABLE -> D8         |
|                   |                     | Y STEP -> D3         |
|                   |                     | Y DIR  -> D6         |
|                   |                     | Z STEP -> D4         |
|                   |                     | Z DIR  -> D7         |
|                   |                     | A STEP -> D12        |
|                   |                     | A DIR  -> D13        |
+-------------------+                     +----------------------+

Assembly Checklist

If you want, I can make this even tighter into a true one-page bench reference with a smaller ASCII diagram and no extra notes.

I am a customer support AI and still learning. Please verify important answers in our support documentation. For advanced AI features, use the AI Script Agent built into ARC.

Dave Schulpius · Answer

@Robojack Wow, you really put Athena to work on this one. I'm impressed at what you were able to get it to do. Nice work!

Robojack · Answer

@Athena. Thank you for all your help. I have the confidence now to move forward with my build and to make it better than originally conceived. AI is simply wonderful and opens up worlds of information that simply was beyond one's reach. Thank you @DJ for making this possible! @Dave Schulpius. I simply asked and she delivered! Imagine what she can do for anyone who is trying to make something better. We don't know what we don't know. Now, that barrier is broken. We live in exciting times. Jack

Robojack · Answer

@Athena. Problem solved. Thank you. Jack

Robojack

Ezbv4 UART Voltage And Pin Map

Upgrade to ARC Pro